Webcam - Hardware

Reply
Topic Options
Tornadoecr
Logi Nu
Tornadoecr
Posts: 2
Registered: ‎11-20-2008
0

s5500 disconnect and load Windows (Vista x64)

[ Edited ]
Options

‎11-20-2008 04:14 AM - last edited on ‎11-20-2008 11:32 PM by Moderator

Recently I bought a webcam S5500.
I am very pleased with the quality and not had any problem with the install and by the work properly with Windows Vista 64-bit.
However after installing it and turn off the pc, removed the camera's USB port and to my surprise the pc is called, and load the operating system.
Follow the same procedure several times and was always the same thing.

Is it normal?

My board is a P5E3

Thank you and I apologize for my bad English
Message Edited by Pegasus on 11-20-2008 11:32 PM
Report Inappropriate Content
Message 1 of 4 (5,871 Views)
 
KachiWachi
Posts: 46,560
Topics: 242
Kudos: 1,008
Solutions: 463
Registered: ‎05-22-2006
0

Re: s5500 disconnect and load Windows (Vista x64)

Options

‎11-20-2008 04:29 AM

Welcome to the Logitech Community Webcam Forum Tornadoecr! :smileyhappy:


Do you mean to say that when you unplug the camera, the PC reboots?


Thanks.
KachiWachi - Webcam Forum Guru (2002), Logi Legend (2007), Distinguished Logi Legend (2010), QuickCam® Team Forums (2007)
(I am not affiliated with Logitech®, Inc., Lithium™ Technologies, Inc., or RightNow® Technologies, Inc.)
  Have you checked your Logitech Forums Private Messages today?  

If you are looking for official Logitech Customer / Technical Support, please >> CLICK HERE <<

In order to help keep the forum content "fresh", please do not post a reply to any thread that is over six (6) months old.

* Please note that I am currently providing "general" troubleshooting assistance in the public forums once 24 hours have passed.
* However, if I am interested in your issue, and for all "advanced" issues, I will be sending you a Private Message before then.
* Thanks.

* PS - If one of my replies has adequately addressed your issue, please click on the "Accept as Solution" and "Give Kudos" buttons, so that this information can benefit others.

New to Webcams? START HERE!

Logitech Webcam Software 2.x (a.k.a. QuickCam 13.x) - Issues and Solutions
Logitech Webcam Software 1.00.1280 / 1.10.1113 (a.k.a. QuickCam 12.x) - Issues and Solutions
QuickCam 11.0.0.1218 / 11.1.0.2030 / 11.5.0.1169 / 11.8.0.1065 / 11.9.0.1263 - Issues and Solutions

Is your problem one of these older, common, known, or repeat issues?     "Everything Macintosh"
How to make your Logitech camera work in an IM                     Are you looking for (older) software?
Why your older Logitech camera *may* not be supported on Windows Vista, 7, 8, and/or on a 64-bit OS
Report Inappropriate Content
Message 2 of 4 (5,864 Views)
 
Tornadoecr
Logi Nu
Tornadoecr
Posts: 2
Registered: ‎11-20-2008
0

Re: s5500 disconnect and load Windows (Vista x64)

Options

‎11-20-2008 04:39 AM

Hello Kachiwachi

I want to thank the readiness in response.

The PC is switched off
When you pull the camera's USB port
The pc turns on without having to resort to the Startup button
Thanks
Report Inappropriate Content
Message 3 of 4 (5,860 Views)
 
KachiWachi
Posts: 46,560
Topics: 242
Kudos: 1,008
Solutions: 463
Registered: ‎05-22-2006
0

Re: s5500 disconnect and load Windows (Vista x64)

Options

‎11-20-2008 10:50 AM

Please make sure that the motherboard has been installed correctly.


Otherwise, please contact ASUS Support for further assistance with this issue.


Thanks.
KachiWachi - Webcam Forum Guru (2002), Logi Legend (2007), Distinguished Logi Legend (2010), QuickCam® Team Forums (2007)
(I am not affiliated with Logitech®, Inc., Lithium™ Technologies, Inc., or RightNow® Technologies, Inc.)
  Have you checked your Logitech Forums Private Messages today?  

If you are looking for official Logitech Customer / Technical Support, please >> CLICK HERE <<

In order to help keep the forum content "fresh", please do not post a reply to any thread that is over six (6) months old.

* Please note that I am currently providing "general" troubleshooting assistance in the public forums once 24 hours have passed.
* However, if I am interested in your issue, and for all "advanced" issues, I will be sending you a Private Message before then.
* Thanks.

* PS - If one of my replies has adequately addressed your issue, please click on the "Accept as Solution" and "Give Kudos" buttons, so that this information can benefit others.

New to Webcams? START HERE!

Logitech Webcam Software 2.x (a.k.a. QuickCam 13.x) - Issues and Solutions
Logitech Webcam Software 1.00.1280 / 1.10.1113 (a.k.a. QuickCam 12.x) - Issues and Solutions
QuickCam 11.0.0.1218 / 11.1.0.2030 / 11.5.0.1169 / 11.8.0.1065 / 11.9.0.1263 - Issues and Solutions

Is your problem one of these older, common, known, or repeat issues?     "Everything Macintosh"
How to make your Logitech camera work in an IM                     Are you looking for (older) software?
Why your older Logitech camera *may* not be supported on Windows Vista, 7, 8, and/or on a 64-bit OS
Report Inappropriate Content
Message 4 of 4 (5,807 Views)